Understand the material.
Install it well, for good.
Aluminium, cover, LED strip and environment work together. Here you will find the key material and temperature notes for the system design.

Aluminium, PMMA and engineering plastics.
| Component | Material / finish | Classification |
|---|---|---|
| Aluminium profiles | Extruded aluminium; EN AW-6060 serves as the reference basis in the data sheet. | Natural or black anodised, or white/black powder-coated, depending on the profile. Concrete-installation profiles to be supplied coated. |
| Anodised | A6/C0 natural and A6/C35 black; reference coating thickness approx. 10 µm. | Appearance may vary between batches. Cut and drill points interrupt the surface. |
| Powder coating | RAL 9010 pure white matt and RAL 9005 deep black matt; reference approx. 65 µm. | Apply LED adhesive tape to a suitable, clean surface; primer is recommended on low-energy coatings. |
| Main cover family | PMMA / acrylic glass; UV- and weather-resistant material base. | The material property is not a confirmation of tightness or protection rating for the finished luminaire. |
| Mini LL cover | PC diffuser LED, depending on the article. | Do not transfer PMMA expansion values to PC without verification. |
| Mounting clips V1/V2/V3 | POM; material version according to the current plastics data sheet. | The current plastics documentation takes precedence over older general material fields. |
| End caps and connectors | Many end caps are made of impact-resistant PS; certain versions and concrete connectors of ABS. | Choose the material according to the specific component; do not describe all accessories as POM across the board. |
Five metres. Twenty degrees.
A noticeable difference.
When heated from 20 to 40 °C, 5 m of aluminium expands by about 2.3 mm and 5 m of PMMA by about 6.3 mm.
The difference is around 4 mm over the entire length. This does not result in a blanket 4 mm gap at each end: fastening, starting temperature, total length, joints and end caps determine the required room for movement.
| Material | Change in length per 1 m / 20 K | At 5 m / 20 K |
|---|---|---|
| Aluminium (reference) | ≈ 0.47 mm | ≈ 2.3 mm |
| PMMA (reference) | ≈ 1.26 mm | ≈ 6.3 mm |
| Difference | ≈ 0.79 mm | ≈ 4.0 mm |
Calculation basis: α Al = 0.0234 mm/(m·K), α PMMA = 0.063 mm/(m·K). Worked example, not a definition of permissible operating temperatures.
The environment decides the performance.
Heat dissipation, profile, cover and installation situation belong together. The following recommendations apply only to the tested combinations from the MPW thermal data sheet.
| Tested design | Recommendation at 25 °C ambient temperature | Recommendation at 45 °C ambient temperature |
|---|---|---|
| Concrete · LL25 / LL35 + V1 | ≤ 22 W/m | ≤ 22 W/m |
| Concrete · LL2515 + V1 / V5 | ≤ 22 W/m | ≤ 15 W/m |
| Flush (UP) in brick, plasterboard, timber, ETICS · LL25/LL35 + V1; LL2515 + V1/V5 per tested combination | ≤ 22 W/m | ≤ 10 W/m |
| Surface-mount/pendant · LL25 + V1 | ≤ 22 W/m | ≤ 10 W/m |
| Surface-mounted/pendant · LL2515 + V5 | ≤ 22 W/m | ≤ 6 W/m |
Thermal behaviour of the luminaire profiles
Original MPW data sheet · verified combinations and output limits
Preserve the surface.
Keep the technology accessible.
For care, use soft, non-abrasive aids and cleaning agents compatible with the material. Avoid aggressive solvents and mechanically abrasive cleaning; check compatibility beforehand in special environments.
Individual material data on moisture, chlorine or weathering are not an approval for a completely assembled luminaire. Sealing, connection, protection rating and thermal design must suit the place of use.
Before maintenance or removal, have a qualified electrician safely isolate the electrical installation. Use the securing of the luminaire insert in a controlled way and check the mechanical and electrical execution after service.
Material temperatures such as Vicat or HDT values from raw-material data sheets are not permissible continuous operating temperatures for the entire system.
Aluminium profiles data sheet
PDF · Original document
PMMA covers data sheet
PDF · Original document
Plastic parts data sheet
PDF · Original document

