Brick masonry
Turn a masonry wall into a lighting surface. LightLineLed leads light lines through stairwells, living areas and hallways – in new builds as well as in refurbishment.

Brick · New build – Plan the system receptacle into the new wall build-up from the start.
Watch on YouTubeBrick · refurbishment – integrate light lines into existing masonry – discover the installation in the video.
Watch on YouTubeWhat this solution makes possible.
An integrated light line can also be created in a masonry wall. The profile with 13 mm flange connects the prepared groove with the finished plaster surface. New build and renovation receive different connection details; the luminaire insert follows after plaster and paint.
Light guidance directly in the wall surface.
Connection to new plaster or existing old plaster.
Transformer technology can sit in a deeper, accessible profile section.
This is how your line of light is made.
Application, construction and benefits – tailored to your architecture.
The wall becomes the carrier of the lighting design
LightLineLed brings the light directly into the masonry wall. A line can accompany a corridor, structure a stairwell or emphasise a room edge, without an add-on luminaire body dictating the surface. The prepared profile channel defines the run; visible profile and cover shape the later termination. Especially with continuous lines across several wall areas, a calm, recurring design language emerges that can be linked with the other LightLineLed applications in the building.
Suitable connections for new build and renovation
The profile with its 13 mm flange creates the connection to the new plaster surface in new construction. For the documented refurbishment variant, the housing is matched to the existing wall and plaster build-up. This provides a clear installation principle for both situations. Planning starts from the finished surface and takes the permissible groove in the masonry into account. This makes it possible to clarify in advance how the light line can be integrated into the existing or new wall build-up.
Combine housing and technology sensibly
Along the light line, the mounting profile receives the visible luminaire insert. Where space for suitable power supply technology and connections is required, a deeper transformer profile section completes the system. This creates a defined technical location within the planned run. The choice of profile, cover and lighting technology is guided by the room effect and lighting task. The line that will later be visible and the installation space behind it can thus be planned together, instead of having to connect them only after the plastering work.
Keep plastering work and lighting installation cleanly separate
While plastering and painting take place, the profile opening remains protected. The prepared luminaire insert is only installed afterwards. For the fit-out this means a clear sequence of trades; for the client, visible surfaces and lighting technology stay protected until completion. With a planned removal path, the suitable insert can be reached again later. Existing cables, wall build-up and permissible chases are checked in advance so that design, installation and long-term use fit together.
The solution in section
The system as construction progresses.
From the prepared housing to the finished light line.
The path to the finished light line
Check the groove and existing structure
Mark out the route and transformer zone, locate existing cables. Assess the permissible chase according to wall thickness, brick type, length and direction; coordinate load-bearing elements with the structural engineer.
Connecting and fastening profiles
Create a groove with room for alignment and fastening. Insert lateral connectors, connect profiles flush and close the transition and ends. Use suitable plugs and screws or a coordinated fastening material.
Create the finished plaster plane
Align the front edge with the later surface. Insert the protective strip; plaster new-build work or repair the connection to existing plaster flush.
Fit and inspect
After the surface work, clean the opening, fit driver and light insert, secure every section and check function and retention seat.
Installation & documents.
The installation and processing instructions accompany the actual implementation of your line of light.
Brick masonry · Installation & processing
PDF · matching instructions
Safety and installation notes
PDF · observe together with the instructions
The complete installation manual
All applications and system details
Processing notes in detailMounting clips, safety cable and further notes on the specific design
Build-up details
Profile body 30.6 mm wide, 66 mm with flanges.
Installation depth from the finished plaster surface: mounting profile 37 mm, driver profile 64 mm. The routing depth is derived from the actual plaster build-up and fastening.
In new construction, the flanges remain under the new plaster. In the refurbishment shown, both flanges are separated beforehand at the break point.
Processing and installation
Mounting clips V2 (20 mm) and V3 (30 mm) may be shortened. Afterwards, both side legs must again taper inwards at an angle and form tips like the original tips. Blunt or straight-cut leg ends cause the clips to break when snapping in. Bevel both legs accordingly, deburr the cut points and check the tip shape before installation. Then check for full snap-in seating and secure hold. Do not use damaged clips. No blanket shortening dimension or cutting angle.
For point-wise profile fixing, use at least two fixing points per light line, spaced no more than 1.5 m apart; the specific fastener must suit the brick and the load.
For the electronics and terminal point, MPW recommends at least 50 cm of driver profile.
The retaining clip of the fall protection locks exclusively into the mounting profile, never into the flush-mount driver profile. If the light line begins with 0.5 or 1 m of driver profile, the upper securing fixing lies only in the adjoining mounting profile. A continuous flush-mount driver profile does not allow this type of securing; every lighting element must still be secured.
Four mounting clips per metre, rounded up and at least two per section. V1: 10 mm, V2: 20 mm, V3: 30 mm – choose to match the actual fit-out height. Secure visible profiles at the start, at every joint and at the end; the connector pair sits in both rear longitudinal slots of the suitable visible profile.
In the flush-mount driver profile, maximum driver installation height is 18 mm; remove the pull-out tab only after complete installation. MPW recommends routing the conduit in at the start of the driver profile, not through the end caps. Keep the electronics, terminal point and inspection access accessible.
Before cutting, measure the temperature of the profile and cover. Allow room for movement at joints and end caps for heating and cooling, and clip in the cover free of stress.
Discover the matching products.
Profiles, covers and accessories together make up your light line. The product pages show versions and matching combinations.

Mounting profile with 13 mm wing
Prepare the line of light together with the board cladding

Driver profile with 13 mm flange
Power supplies and terminal points accessible via the light line

LL25 profile – the all-round visible profile
Consistent design language for recessed, surface-mounted and pendant installations

Recessed and visible profile LL35F
Visible aluminium edge covers the connection joint

Visible profile LL2515
Compact aluminium body with sculptural V5 cover

Corner visible profile LL2511E
45° inclined light-emitting surface for targeted aiming

Mounting clips V1, V2 and V3
Height adjustment within the intended combination

Fall protection for profiles with flange
Connecting and securing at the profile joint
Light line found.
We'll clarify the details together.
Building material, surface and desired lighting effect set the direction. MPW supports you with the right system version and the next steps.
More possibilities for your architecture.
The solution. Experienced in the room.
Light lines in the finished room: the images show layout, integration and light effect. Open an image to enlarge the full shot.


